The control of indoor temperature must be able to handle large time constants and both measureable disturbances like outdoor temperature, and non-measurable disturbances, like waste heat from appliances. Due to cheaper microcontrollers (small computers with designated tasks) with better performance, more advanced and computation-demanding methods for control can be used.In this thesis, Generalized Predictive Control (GPC) has been implemented and tested on a theoretically derived model of a house. GPC states that a model of the system is estimated in every sample, and the control is carried out simultaneously, based on predictions of the model. Disturbances like solar radiation can be estimated and used in the control as well. The control signals are determined by quadratic programming, which makes it possible to consider conditions, for example limitations on the control signals.GPC requires a number of parameters to be defined, like model order and control signal penalty, but is relatively robust for variations in them.

This thesis has been conducted at Saab Bofors Dynamics AB. The purpose was to investigate if a non-linear missile model could be stabilized when the optimal control signal is computed considering constraints on the control input. This is particularly interesting because the missile is controlled with rudders that have physical bounds. This strategy is called Model Predictive Control. Simulations are conducted to compare this strategy with others; firstly simulations with step responses and secondly simulations when the missile is supposed to hit a moving target.

In industrial control systems PID-control remains the prevalent strategy, also for processes that would benefit from model based control. The purpose of this thesis is to evaluate whether model based control can be readily implemented in an industrial control system. To this end a simulated surge tank with a simulated industrial control system is studied. For evaluation two scenarios with specified objectives are selected.Following a review of LQR and versions of MPC, Predictive Functional Control (PFC) is considered the most suitable for implementation. PFC is a form of MPC developed with industrial applications in mind and therefore has several advantages for implementation in an industrial control system.

This master?s thesis describes the development of a model of the catalystsystem aiming at control by an MPC. A well functioning model, which is suitable in control purpose, is important while emission legislation become more and more hard to fulfill for the car manufacturers. Much research has been done in the field of physical modeling of the system, but in this work a linear adaptive time discrete ARX-model is developed and validated.The systems tendency to change its dynamic during usage implies that the model must be adaptive. The developed model proved to be well functioning and shows promising conditions for the MPC design.

This master thesis deals with problems in the arc length control in Pulsed MIG/MAG Welding. The main problem is that it is not possible to measure the arc length. In the present solution the voltage over both the electrode and the arc represents the arc length. To improve the arc length control a model of the electrode melting has been built. One output from the model is the voltage over the electrode and with this voltage together with the measured voltage it is possible to calculate the voltage over just the arc.

When a helicopter is flying, the dynamics vary depending on, for example, speed and position. Hence, a time-invariant linear model cannot describe its properties under all flight conditions. It is therefore desirable to update the linear helicopter model continuously during the flight. In this thesis, two different recursive estimation methods are presented, LMS (Least Mean Square) and adaptation with a Kalman filter. The main purpose of the system estimation is to get a model which can be used for feedback control.

Our purpose with this qualitative study is to investigate how teachers experience their work situation, using Karasek and Theorell?s demand-, control- and support model. The study is based upon ten semi-structured interviews with gymnasium teachers. The interviews were transcribed and coded with three different themes; demand, control and support. We analyzed the results with Karasek and Theorell?s mentioned model.

Denna magisteruppsats redogör för en anpassning av COCOM (Contextual control model) till flygledningsdomänen. COCOM är en modell som kan användas för att beskriva och förutse kontroll hos operatörer i komplexa system. En central del av modellen är begreppet kontrollnivå vilket beskriver hur graden av kontroll hos ett JCS (Joint Cognitive System) beror av och påverkar de parametrar som beskriver dess prestation. Fokus i denna uppsats ligger på det JCS som omfattar flygledaren i sin arbetsposition.I uppsatsen anpassas Hollnagels generella beskrivning av kontrollnivåer i COCOM till flygledningsdomänen. Till grund för anpassningen ligger en kvalitativ studie i form av observation och intervju av sju operativa flygledare vid en svensk kontrollcentral.

This report treats two assignments that concerns the biofuel furnace at Billerud Skärblacka AB and how these assignments were solved. The assignments were: reducing the number of CO-spikes and tuning the overfire air control loop. To reduce the number of CO-spikes the possibility that skewness in mass distribution affects the number of CO-spikes were study. The skewnwss of mass distribution was controled and adjusted with two experiments. The conclusion that was made is that the skewness of mass distribution were not sufficient enough to affect the number of CO-spikes.

In the pulp industry, digesters are used to disolve lignin in wood chips. The concentration of lignin is measured and is called the Kappa number. In this thesis, the question of whether an online Kappa sensor, taking samples from the mid-phase of the digester, is useful or not is analyzed. For the samples to be useful, there has to be a relationship between the measured Kappa at the mid- phase and the measured Kappa in the blowpipe at the bottom of the digester. An ARX model of the lower part of the digester has been estimated.

Spotify is a music service that offers on-demand streaming and is available in several countries worldwide. As the company and the interest for it grows, more and more parties are involved and those involved, including the record labels want to control and get an overview of their products. They want to be able to see, for example, when a product is available on Spotify and in which countries.Spotify is in May 2013 in process of developing a to be used by administrators on Spotify in order to meet the record labels with the information requested. The new software intends being used by administrators but also by the record labels so that they will be able to overview their products availability.We were asked by one of the developers to conduct user interviews and tests to result in a design proposal on how the display page of information about a product could be visualized more clearly so that it suits both record labels and employees at Spotify. The results of our contextual interviews were translated into a prototype with two display pages.

To enable the enhancement of the driver's environment in a forklift, an alternative form of steering has been evaluated. An earlier concept with a combined driving and steering wheel has been exchanged to a concept with two driving wheels. A link wheel has replaced the combined driving and steering wheel. The steering is done through differentiation of the velocities of the two driving wheels. The scope of this master thesis is to create a simulation model, create a control program and to evaluate the concept of two driving wheels.

A cars powertrain consists of everything that is needed for its propulsion. The components in the driveline that transfer the power from the engine to the driven wheels are not absolutely stiff, hence they will wind up due to the torque and act as torsion springs. If you suddenly demand a bigger torque by stepping on the accelerator pedal, a so called tip in manoeuvre, and that torque is acquired from the engine as quickly as possible, the driveline will not be able to transfer that fast torque change due to its weakness and as a result it will start to oscillate. These oscillations will be transferred to the driven wheels and make the car to accelerate jerkily which will be experienced as uncomfortable by the passengers. Furthermore, there is a backlash in the driveline that will make the weakness in the driveline even more excited than it should have been if the backlash did not existed.To avoid too big problems with these oscillations there is a control system that controls the demanded torque.

This master thesis is made of two parts. The first part concerns the method and results ofdesigning a motion control system for a piece of research-equipment called BIRGIT. Theequipment is made to be used for research on eyemovements. In the second part, a computermodel of a part of the balance organ in the inner-ear is developed. The work has been done atthe Bernadotte laboratory at S:t Erik Eye Hospital.The equipment the control system is made for is a so-called rotationchair.

For research purposes Saab has developed a generic mathematical model denoted VEGAS of an aircraft with a configuration similar to JAS 39 Gripen. Today parts of Gripen backup control system are used also for VEGAS making the system subject to both corporate and defense secrecy. The main objective of this master thesis is to design, verify and implement public pitch axis flight control system for VEGAS. Furthermore, simplifications regarding the design process is to be examined. Design of pitch axis flight control system for the entire flight envelope has been carried out.